Claude Weekly Limit: All Models Explained (Pro, Max, and Opus)

Claude Code enforces a weekly usage cap that sits on top of the 5-hour rolling window limit. The weekly cap resets 7 days after it first started filling, and the amount you get depends on your plan (Pro vs Max) and which model you're using. Opus 5 consumes the budget fastest; Haiku barely dents it. As of August 2026, Anthropic has not published exact token numbers for these caps, but the behavior is consistent and well-documented by users.

• Pro plan: lower weekly cap, suited for moderate use
• Max plan ($100/mo): roughly 5x more usage than Pro; Max plan ($200/mo): roughly 10x more
• Opus 5 consumes the cap ~5x faster than Sonnet 5 for equivalent tasks
• The weekly cap and the 5-hour window are independent limits — you can hit either one first

What is the Claude weekly usage limit?

The weekly limit is a rolling 7-day usage budget applied to your Claude Code subscription. Once you exhaust it, Claude Code pauses until the oldest usage falls outside the 7-day window and frees up capacity. It is separate from the 5-hour rolling window, which is a shorter burst limiter. You can hit the 5-hour window first on a heavy session, or hit the weekly cap first if you've been running Claude Code all week.

According to Anthropic's support documentation, usage limits for Claude Code are "based on a combination of your subscription plan and current demand." The exact token counts are intentionally not published — Anthropic adjusts them dynamically based on server load.

How does the weekly limit differ by model?

Every model pulls from the same weekly budget, but heavier models consume it faster. Opus 5 is the most expensive model Claude Code can invoke, and a single long agentic session with Opus can consume what Sonnet would use in several sessions. Haiku, at the other end, is cheap enough that most users never notice it eating into their weekly cap.

Model	Relative weekly budget consumption	Best for
Claude Opus 5	Highest (5x Sonnet)	Complex reasoning, hard bugs
Claude Sonnet 5	Medium (baseline)	General coding tasks
Claude Haiku 3.5	Lowest (~0.2x Sonnet)	Autocomplete, small edits

If you're consistently hitting the weekly cap, switching from Opus to Sonnet for routine tasks is the fastest way to stretch your budget. See also: how to reduce Claude Code token usage.

How do Pro and Max weekly limits compare?

The Max plan exists specifically to give heavy Claude Code users more headroom. As of August 2026, the Max $100/mo tier gives approximately 5x the usage of Pro, and the Max $200/mo tier gives approximately 10x. This ratio holds across all models — so Max on Opus still burns faster than Pro on Sonnet, but you get significantly more total capacity.

Plan	Monthly cost	Weekly cap (relative)	Claude Code access
Pro	$20/mo	1x	Yes (limited)
Max	$100/mo	~5x	Yes (heavy use)
Max	$200/mo	~10x	Yes (power users)

For a deeper breakdown of whether upgrading is worth it, see Claude Pro vs Max limits.

When does the weekly limit reset?

The weekly limit resets on a rolling 7-day basis tied to when you first started using usage in that window, not a fixed calendar day. This means there is no universal "Monday reset" — your reset time is personal to your usage pattern. If you started a heavy session on Wednesday, your oldest usage will roll off the following Wednesday.

You can check your current reset time at claude.ai/settings/usage or by running /usage inside Claude Code. For more detail, see when does Claude Code usage reset and what timezone does Claude usage reset in.

What is the difference between the weekly limit and the 5-hour window?

Claude Code applies two independent rate limits simultaneously. The 5-hour rolling window is a short-term burst cap: it prevents any single 5-hour stretch from consuming too many tokens. The weekly cap is the longer-term ceiling on total usage over 7 days. You will hit whichever limit you reach first — and they do not share state.

• 5-hour window hit: You coded hard for a few hours. Claude pauses for the remainder of that 5-hour block, then resumes.
• Weekly cap hit: You've been building all week. Claude pauses until usage older than 7 days rolls off your account.
• Both can happen: On an intensive project you might hit the 5-hour window daily and eventually drain the weekly cap too.

For a full comparison, see Claude Code weekly limit vs 5-hour lockout.

How do you check current usage before hitting the weekly limit?

There are three ways to monitor your Claude Code usage before you hit the cap:

1. /usage command: Type /usage in any Claude Code session to see a snapshot of your current 5-hour window and weekly cap status.
2. claude.ai/settings/usage: The web dashboard shows a graphical breakdown of your usage over time, by model.
3. Usagebar: A $9 one-time macOS menu bar app that tracks your 5-hour window, weekly cap, and context usage in real time — with notifications at 50%, 75%, and 90% of each limit so you're never caught off guard.

Of the three, Usagebar is the only option that gives you proactive alerts. The /usage command and web dashboard are reactive — you have to remember to check them. See also: how do I check my Claude Code usage limits and how to check Claude Code reset timer.

Get Usagebar — $9 one-time, tracks all three usage dimensions with menu bar notifications.

Can you reset the weekly limit early?

No. There is no official way to reset the weekly cap before it naturally rolls off. Logging out, restarting Claude Code, or switching projects does not clear your usage counter. The only exception is upgrading from Pro to Max — that gives you a larger cap on the new plan, which may feel like a reset if you were near the Pro ceiling. For more, see can you reset Claude usage limit early.

Key takeaways

1. Claude Code has two independent limits: a 5-hour rolling window (burst) and a 7-day rolling cap (weekly).
2. The weekly cap is plan-dependent: Max $200/mo gives roughly 10x the Pro budget.
3. Model choice matters: Opus 5 consumes the weekly cap ~5x faster than Sonnet 5.
4. Resets are rolling, not calendar-based — your reset time depends on your usage history.
5. Check usage via /usage, the web dashboard at claude.ai/settings/usage, or Usagebar for proactive alerts.
6. You cannot reset the cap early — plan your heavy sessions accordingly.

Sources

• Anthropic Support: Using Claude Code with your Pro or Max plan
• Anthropic Documentation
• Claude.ai Usage Settings